BreezeMAX Extreme is part of the carrier-class, field proven BreezeMAX product family and is the first wireless broadband solution to bring WiMAX 16e. BreezeMAX® Extreme WiMAX™ 16e pioneer for the license-exempt market WiMAX 16e for the License-exempt Market Main Features and Highlights. BreezeMAX Extreme is part of the carrier-class, field-proven BreezeMAX product family and brings WiMAX 16e technology to the 5 GHz license-exempt.
|Published (Last):||14 July 2012|
|PDF File Size:||17.5 Mb|
|ePub File Size:||5.74 Mb|
|Price:||Free* [*Free Regsitration Required]|
No disclosure thereof shall be made to third parties without the express written permission of Alvarion.
BreezeMAX ® Extreme 5000
Aradial default installation of version 5. Radiator verified with version 4. NE failure when provisioning a capacity limit CPE model with services sum exceeding the capacity limit. When connection with AAA is reestablished the entire cell will be authenticated again breezemmax de-registration of all CPE.
De-register the MS to have the new setting in affect Recommended workaround is to minimize GPS holdover events — improving antenna installation location insure clear skyuse high gain profile antenna When the sum of all provisioned services exceeds the CPE license capacity, the NE process will not be completed.
Please note, when downgrading from Release 1. When using forwarding with option 82, if the Service Group gateway is a Cisco router the following configuration must be add on the Cisco to permit the Extre,e packets to pass: It is important to design carefully the frequency allocations and potential bands e.
It’s a community-based project which helps to repair anything. Each manual covers all relevant topics associated with the respective equipment, including: Alvarion reserves the right to alter the specifications in this publication without prior notice.
It corresponds to 5000 versions: Two service flows which have the same priority are equalized by the CPE at packet rates and not bit rates the packet sizes brezemax not taken into account. Specifically when operating a dual-carrier BTS e.
When running Spectrum Analyzer while operating in dual sector mode, if system had developed misssynchronization because of GPS holdover, at the end of the scan process the system would reinitialize both channels. When using Optimized Video service, it is recommended not to use DSCP values of 1, 8 and 9 for uplink data traffic other than video.
When BTS is operating with Release 1. There exyreme no issue observed with Ping messages of length up to 14K bytes. Backhauling link must be under Eth. As part of these changes, several additional configuration options are available, such as: In very rare occasions, the logical BS ID might be reinitiated.
Alvarion BreezeMAX Extreme Wireless Broadband Solution – Alvarion
When operating with DHCP option 66 and 67, the CPE might not receive an IP if option 67 is not used only 66 or if the option 67 xml file is not at the specified location. The value may range between 1.
Cable to mains is NOT included and should be ordered separately. The situation is auto recoverable and service is restored after few seconds. Ping messages of bytes transmitted over R1 to the host behind CPE are sometimes wxtreme.
If static routes are added to a device extrdme as DHCP client the routed classes will not perform traffic. Network entry timeout prevent s full band scan in universal CC, thus workaround is needed to set only one BW to scan. The documentation includes the following: After switching between Operation Modes e.
Due to FCC regulation requirements, starting with release 1.
Define new service interface as Eth. Recovery actions in case BTS was upgraded to 1.
BreezeMAX ® Extreme |
Under GPS chaining, when there is a faulty chaining cable, the radio units in the chain may not initiate transmission. Update the Service Profile type per your needs e. Note that these can be overcome with additional scripts and configuration of the default installed Radiator Eztreme In case of using country code with DFS: CSassociate vreezemax it the forwarding rule you’ve created in step ‘b’. This is mainly since IP address Upgrade to Release 1.
One may need to implement timers or other logic scripts in the AAA breezeamx close these sessions. Such DSCP values might interfere with the feature. Although mentioned in recommendation 20, when operating in release 1. Due to the requirements of FCC regulations, starting with release 1.
When upgrading to release 1.