LM R e Thin Film Resistor Network. 0 05% Matching and 5 ppm This datasheet has been download from: Datasheets for electronics components. On all operational amplifier data sheets, the specifications listed on the deep in the data sheet. .. , LM and LT with improved price/performance. LM Datasheet: LM Precision Operational Amplifier, LM PDF Download National ->Texas Instruments, LM Datasheet PDF, Pinouts, Data Sheet.

Author: Daizahn Bakora
Country: Mauritius
Language: English (Spanish)
Genre: Technology
Published (Last): 7 October 2016
Pages: 61
PDF File Size: 20.83 Mb
ePub File Size: 13.28 Mb
ISBN: 570-2-82913-231-9
Downloads: 47029
Price: Free* [*Free Regsitration Required]
Uploader: Dashakar

This datasheet has been downloaded from: Its long-term stability is typically 3 to 10 ppm per hours when held near Tmax, and slightly better when operated at room temperature. However, avoid overloads at high ambient temperatures, as a prolonged short-circuit may cause the junction temperature to exceed the Absolute Maximum Temperature.

Consult factory for availability of devices with tighter Accuracy and Tempco Specifications. This point occurs when the device is required to sink approximately 1.

LM607 PDF Datasheet浏览和下载

For example, datashert the output were trimmed up to Ceramic capacitors may seem to do the job, but are not recommended for production use, as the high-K ceramics cannot be guaranteed for dtasheet leakage, and may exhibit piezo-electric effects, converting vibration or mechanical stress into excessive electrical noise.

The output can sink current as well as source it, but the output impedance is much better for sourcing current. The output is short-circuit-proof to ground. These pins would not be damaged by a short to ground, or by Electrostatic Discharges; however, keep them away from large transients or AC signals, as stray capacitance could couple noises into the output.

Unless otherwise noted, these conditions apply: Trimming to a wider range is possible, but is not recommended as it may degrade the Tempco and the Fatasheet linearity at temperature extremes. A military RETS electrical test specification is available on request. Thermal regulation is defined as the change in the output voltage at a time T after a step change of power dissipation of mW.


The LM also provides excellent stability vs. The output has a class-B stage, so if the load current changes from sourcing to sinking, an output transient will occur.

These daatasheet may be cut off if desired. The capacitor used should be a low-leakage type.

(PDF) LM Datasheet PDF Download – Precision Operational Amplifier

In some applications it may be advantageous to datashet the output to either Vin or to ground, to avoid this crossover point. Consult factory for availability of devices with Guaranteed Long-term Stability. If the output is pulled to a positive voltage such as a 15 or a 20V, the output current will be limited, but overheating may occur.

The LM datassheet suitable for limited-temperature operation. The curves showing the Noise vs. In Sinking mode, connect 0.

The LM is recommended for applications where the highest stability and lowest datasheet is required over the full military temperature range. LM see curve above: Capacitance in the Typical Performance Characteristics section datazheet graphically that a modest capacitance of pm607.

They are based on a buried adtasheet reference as pioneered in the LM references, but do not require any heater, as they rely on special temperature-compensation techniques Patent Pending. Changes in output voltage due to heating effects are covered under the specifications for Thermal Regulation and Tempco. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the datasheeg support device or system, or to affect its safety or effectiveness.

Alternatively, a shield foil can be laid out on the printed circuit board, surrounding these pins and pin 5, and this guard foil can be connected to ground or to Vout, effectively acting as a guard against AC coupling and DC leakages. Avoid such overloads for voltages higher than a 20 V, for more than 5 seconds, or, at high ambient temperatures. There is no guarantee that the Specified Temperatures are exactly at the minimum or maximum deviation. A trim pin is available which permits fine-trimming of Vout, and also permits filtering to greatly decrease the output noise by adding a small capacitor 0.


These limits are not to be used to calculate outgoing quality levels. Contact the factory for availability of devices with proven long-term stability.

LM607 Datasheet PDF

The devices have a The trim pin pin 5 should also be guarded away from noise signals and leakages, as it has a sensitivity of 15 millivolts of DVout per microampere. Documents Flashcards Grammar checker. National Semiconductor Europe Fax: Life support devices or systems are devices or systems which, a are intended for surgical implant into the body, or b support or sustain life, and whose failure to perform, when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user.

To avoid this transient, it may be advisable to preload the output with a few milliamperes of load to ground.

Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Do not connect anything to these pins, or improper operation may result.

The device does not include a thermal shut-down circuit. The trim scheme is such that individual resistors are cut open rather than being trimmed partially cutto avoid resistor drift caused by electromigration in the trimmed area. Regulation is measured at constant temperature using pulse testing with a low duty cycle. The LM has a Class B output, and will exhibit transients at the crossover point. Pin numbers for H, M or N packages.

Tsimshatsui, Kowloon Hong Kong Tel: